First Step: Remove the Old Wood Flooring<\/h2>\n\n\n\n
Before we can show you how to replace your wood flooring you need to get rid of the problem areas. We recommend picking an out-of-the-way area to start. Once you get the hang of things, you can move back into those high-traffic areas towards the center of your living room.<\/p>\n\n\n\n
The first step in repairing wood flooring is to size up the area to be repaired. You want to remove as much of the damaged wood as possible. Wood putty doesn’t look good, so don’t try and save a piece that’s 80% good unless you absolutely don’t have enough replacement material. <\/p>\n\n\n\n
We also like to get a birds-eye view of the work to be done. This especially helps you prioritize when you have multiple locations that need replacing. Once you map out the best way to allocate your replacement wood for the repair, you can get started on your first area.<\/p>\n\n\n\n
Making the First Cuts<\/h3>\n\n\n\n
Starting with a circular saw, make two rip cuts down the middle of the first board. You want to rip two lines because you want to remove the wood by pulling it horizontally away from the adjacent boards. You don’t want to lift upward as that would damage the tongue of the pieces you intend to leave in place. We prefer using a circular saw we can connect to a shop vac, thereby minimizing dust.<\/p>\n\n\n\n
![\"Ripping](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-process-1-800x533.jpg\")
<\/a>Prying Out the Bad Board<\/h3>\n\n\n\n
After you’ve ripped a couple of channels into the wood, you can then use a small flat bar or pry bar to remove the channel.<\/p>\n\n\n\n
![\"Using](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-process-2-800x533.jpg\")
<\/a><\/figure><\/div>\n\n\n\nOnce the channel is removed you can coax the remaining wood out and clean the area of the wood flooring you intend to repair.<\/p>\n\n\n\n
![\"removing](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-process-3-800x533.jpg\")
<\/a><\/figure><\/div>\n\n\n\nKeeping Partial Boards in Place<\/h3>\n\n\n\n
Keep in mind that if you don’t need to remove an entire board when you repair wood flooring. You can use an oscillating multi-tool to cut a perpendicular line across the wood to form a break point. Make sure you make the cut right over the center of a floor joist. That gives you somewhere to nail the new board:<\/p>\n\n\n\n
![\"How](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-process-4-800x533.jpg\")
<\/a>Removing Tough Boards<\/h3>\n\n\n\n
You don’t want to break any tongues off adjacent boards. Should you run into difficulty removing part of a board, make a wedge-shaped notch cut near the end using your oscillating multi-tool. This lets you swing the wood back on itself safely without breaking off the tongue of the adjacent piece of the wood flooring you’re not repairing.<\/p>\n\n\n\n
![\"How](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-process-5-800x533.jpg\")
<\/a>Installing New Wood Flooring<\/h2>\n\n\n\n
After the difficulty of removing wood, adding in the new piece seems like child’s play. You do want to measure and cut very carefully to minimize the number of gaps between the pieces of wood. We cut the wood outside, using a cordless circular saw and then brought it in for final installation. You could also use a miter saw<\/a>.<\/p>\n\n\n\n Finish the wood flooring installation by using a finish nailer to fasten the boards directly to the joists. Our 1920’s home had no underlayment so we had to pick our fastening points carefully. Two pops per joist are sufficient, and you’ll want to angle the nails. This holds especially true at the ends to ensure the new wood stays secure. The final steps will serve to fill in the gaps and small nail holes.<\/p>\n\n\n\n Finishing the wood involves a few steps. First, you need to use a belt sander to get the wood flush with the adjoining pieces. Remember to use a tool you can connect to a shop vac to again pick up the majority of dust during this step:<\/p>\n\n\n\n After you’ve sanded the wood flush, use an orbital sander to provide the secondary level of sanding. This lets you achieve a smooth surface suitable for your clear coat finish.<\/p>\n\n\n\n![\"How](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-800x533.jpg\")
<\/a>Finishing the Wood<\/h2>\n\n\n\n
![\"How](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-process-6-800x533.jpg\")
<\/a>![\"How](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-process-7-800x533.jpg\")
<\/a><\/figure><\/div>\n\n\n\n
![\"Applying](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-process-8-800x533.jpg\")
<\/a><\/figure><\/div>\n\n\n\n![\"finished](\"https:\/\/www.protoolreviews.com\/wp-content\/uploads\/2011\/02\/How-to-Repair-and-Replace-0.75-inch-Wood-Flooring-process-9-800x533.jpg\")
<\/a><\/figure><\/div>\n\n\n\n